Mazda Cylinder Head

Browse Mazda Cylinder Head questions and answers. Choose a question that matches your symptoms.

142 discussions


Heater Will Not Blow Hot Air--only Luke Warm--radiater...

1990 MAZDA B2200
Heater Will Not Blow Hot Air--only Luke Warm--radiater Is Full--tempature Knob Is As High As It Will Go.--had Recent Head Gasket Replaced...
1 ANSWER
Asked by Anonymous

1990 Mazda 323 - Coolant / Temp Issues

1990 MAZDA 323
Cracked Radiator Led To Overheat & Blown Head Gasket. All Fixed Now + New Thermostat + New Alternator & Battery & Been Running Ok For Last 4...
1 ANSWER
Asked by slbazza

No Compression After Changing Head Gasket?

1989 MAZDA B2200
Recently Replace The Head Gasket On My Truck. Now It Will Not Start. It Has 25 Psi Compression After Doing Compression Check. Turns Over...
15 ANSWERS
11 IMAGES
Asked by Cleesouthwick

Setting Timing After Head Works

1989 MAZDA B2200
I Have A Mazda(89) B2200,2.2motor That Did A Head Job On.i Have Set The Bottom Tdc Mark,piston Is Up,dist. Pointed At No 1. My Question Is...
8 ANSWERS
2 IMAGES
Asked by itile4u

1989 Mazda B2600

1989 MAZDA B2600
Are There Any Common Problems With The B2600i That I Should Know About? The Previous Owner Blew The Head Gasket And Then Let It Set For Like...
1 ANSWER
Asked by DjAsOn

1989 Mazda MX6 Head

1989 MAZDA MX6
Engine Mechanical Problem 1989 Mazda Mx6 Manual How Long Would It Take To Replace A Head In This Car
1 ANSWER
Asked by doneewicklund

1989 Mazda 323 Question On The Heads

1989 MAZDA 323
Engine Mechanical Problem 1989 Mazda 323 4 Cyl Two Wheel Drive Manual Would The Head From A 1987 Mazda 323 Be Compatable With A 1989...
1 ANSWER
Asked by dougrock183

1989 Mazda Truck HEAD GASKET

1989 MAZDA TRUCK
Could You Give Me An Estimate On What It Would Cost To Replace Head Gasket Including Labor
1 ANSWER
Asked by KAYCE09

1989 Mazda Truck Head Gasket Installation

1989 MAZDA TRUCK
When Installing A New Head Gasket, Should Anything Be Used Between The Head And The Gasket? Would The Use Of An Adhesive Or Gasket Sealer...
2 ANSWERS
Asked by ssbriggs1996

1989 Mazda 929 Head Gasket Replacement

1989 MAZDA 929
Long Diatribe So There's A Donation:-) A Timing Belt Idler Pulley Bolt Sheared Off And Made A Pretty Total Mess Out Of The Engine. The Bolt...
3 ANSWERS
Asked by rmmagow

Browse other repair topics

Browse by repair topic
SymptomsAir FilterAir Intake Temperature SensorAir Intake TubeBalance ShaftBlockCamshaftComputerCoverCrankshaftCrankshaft PulleyCylinder HeadDipstickDrain PlugEstimateFlexplateGround StrapHarmonic BalancerIdentificationIdle Air ControlIntake ManifoldInterchangeKnock SensorMAP SensorMass Air Flow SensorMountOilOil ChangeOil CoolerOil Fill CapOil FilterOil PanOil Pressure SensorOil PumpOxygen SensorPistonRebuildReplace/RemoveSerpentine BeltStarterSuper ChargerThrottle BodyTiming BeltTiming ChainTune-upTurboVacuum Hose DiagramWiring

    Can’t find your issue?

    Ask a new Mazda question