GMC Engine

Browse GMC Engine questions and answers. Choose a question that matches your symptoms.

4,523 discussions


Hard Start Up In The Morning

2009 GMC TERRAIN
Hello In The Morning It Does Not Start Up From First Try And The Next Problem Is The Idle Is Too Low And When I Put It In Drive The Rpm's...
15 ANSWERS
3 IMAGES
Asked by Mohamad kibrit

Misfire

2009 GMC ACADIA
My Check Engine Light Came On And The Truck Started Running Like Crap. Took It To Autozone. The Codes Said That All Six Cylinders Were...
2 ANSWERS
Asked by golfnlance

2009 GMC Sierra Cylinder 8 Misfire

2009 GMC SIERRA
I Have Had A Cylinder 8 Misfire On My Truck For A Moth And Have Replaced The Spark Plug, Wire, Ignition Coil, Fuel Injector And Have Done...
3 ANSWERS
Asked by Lax4life

2009 GMC Acadia Timing Chain Marks

2009 GMC ACADIA
I Need To Know Where The Marks Are For Number 7 And 8 For The Timing Belt For The Above Car.
1 ANSWER
Asked by virgo2267

Have A 5.3 Flex Fuel Truck, Check Engine Light Code...

2009 GMC SIERRA
Have A 5.3 Flex Fuel Truck, Check Engine Light Code Says Camshaft Position Sensor. Planning On Replacing It, My Question Is Would The...
2 ANSWERS
Asked by Anonymous

Electricty

2009 GMC YUKON HYBRID
2009 Yukon Hybrid Was Rear-end At 70mph. It Has Been Repair And Retuurn To The Next Morning Will Not Start ,and Read Out Everything Need To...
1 ANSWER
Asked by james534us

2009 GMC Acadia GMC Acadia 2009 Engine Fumes

2009 GMC ACADIA
Gmc Acadia 2009, Mileage 350 First Hand, Unusual Smog From Exhaust Pipes, Blackened Exhaust Pipes From Inside, Suspected Oil Burn Smells...
1 ANSWER
Asked by tariq54

No Start After Pulling Engine For Timing Chain...

2008 GMC ACADIA
I Recently Purchased This Car As A Mechanic Special Due To A Loose Timing Chain Causing The Cams To Go Out Of Time. After Pulling The Engine...
1 ANSWER
2 IMAGES
Asked by Ckramlich

Power Loss?

2008 GMC SIERRA
I Have The Truck Listed Above At Half Throttle, My Truck Moves Like A Turtle. I've Notice On My Dash Prd321 Usually Has A Line Indicator...
1 ANSWER
Asked by Slyau

I'm Changing Out The Seal On My Crankshaft?

2008 GMC ACADIA
I'm Changing Out The Seal On My Crankshaft I Removed The Bolt But I Can't Get The Pulley Off I Have A Large Gear Pulley?
1 ANSWER
9 IMAGES
Asked by Tinabell90

Browse other repair topics

Browse by repair topic
SymptomsAir FilterAir Intake Temperature SensorAir Intake TubeBlockCamshaftComputerCoverCrankshaftCrankshaft PulleyCylinder HeadTickDrain PlugFlexplateFlywheelGround StrapHarmonic BalancerIdentificationIdle Air ControlIntake ManifoldInterchangeKnockMAP SensorMass Air Flow SensorMountOil LeakOil ChangeOil CheckOil CoolerOil Fill CapOil FilterOil PanOil Pressure SensorOil PumpOxygen SensorPistonRebuildReplace/RemoveSerpentine BeltStarterSuper ChargerThrottle BodyTiming BeltTiming ChainTune-upTurboVacuum Hose DiagramWiring

    Can’t find your issue?

    Ask a new GMC question