Transmission problems?

Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
You are welcome.

Always glad to help.

Happy New Year.

Roy
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
PABSH32
  • MEMBER
  • 1 POST
  • 1998 FORD EXPLORER
  • 95,000 MILES
I have changed the torque converter and the valve body and put it all back together and now when I put the auto transmission oil in it will only take about 6.5 litres before it comes out of the overflow and it will not engage in any gears the shifter will move thro the gear ranges but there is nothing can u help I was wandering if it was the transmission fluid pump at fault if I replace this will it solve the problem
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
You need to diagnose the problem and locate the source before taking anyu action. You have already wasted so much time and money on it because of guessing.

The transmission would not take too much fluid at one go. You need to fill some, start engine, shift through gears, check level and top up again.

What was the initial problem for you to replace those parts?
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
Sounds like the vent to the trans is plugged or onen of the things you replaced like the valve body may bewrong. It may be full as well. Besides it only takes 9.5 qts to fill it anyhow. Before you pull the trans, have a trans guy run a scan on it, it may be an electrical problem or one of the clutch failed. Why did you start doing this stuff anyhow?
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
2CP-ARCHIVES
  • MEMBER
  • 4,540 POSTS
  • 1998 FORD EXPLORER
  • 120,000 MILES
Transmission will not go into reverse. What is the procedure to find out the cause
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
JACOBANDNICKOLAS
  • MECHANIC
  • 109,755 POSTS
If the check engine light is on, have the computer scanned to identify possible transmission trouble codes. Other than that, you need to make sure the fluid is clean and full. Also, trans pressure will need checked to see if that is an issue. A trans tech will need to check that for you.
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
FANNIE COLVIN
  • MEMBER
  • 1 POST
  • 1998 FORD EXPLORER
  • V6
  • AWD
  • AUTOMATIC
  • 180,000 MILES
My vehicle runs fine for like two minutes, then it will not go into gear. I turned it off and unplugged the battery and reconnect it and it runs fine for a few minutes. If you try to shift to another gear the transmission will not respond. I have to unplug battery, reconnect and start again.
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
Scan for codes it may be a transmission selector switch problem.
Was this
answer
helpful?
Yes
No
+1
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
RENEE L
  • ADMIN
  • 1,260 POSTS
Here is a link to an article that features written step by step instructions and pictures explaining how to do the scan yourself, also I have included a link to our YouTube channel with a how to video on code scanning. Most scanners are inexpensive to purchase, you can purchase one from Amazon.com. Once you have the codes please get back to us so that we can further assist you. Thank you for visiting 2CarPros.

https://www.2carpros.com/articles/checking-a-service-engine-soon-or-check-engine-light-on-or-flashing
https://youtu.be/YV3TRZwer8k
Was this
answer
helpful?
Yes
No
+1
Wednesday, December 23rd, 2020 AT 10:31 AM (Merged)
Tiny
DAVEWILCOX
  • MEMBER
  • 1 POST
  • FORD EXPLORER
My 2002 ford explorer 4x4, 4.6 litre engine. Has a bad computer for the four wheel drive. I removed it to get the numbers off of the case.
After I put the old oneit back on it won't go into any gear.I did not disconnect the battery cable when I took off the computer and put it back in. Will this be solved when I get the new Computer? Please help as I am stranded!
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:34 AM (Merged)
Tiny
SGALLEW
  • MEMBER
  • 3 POSTS
This might sound simple, but try disconnecting your battery for about 3 to 5 minutes. This sometimes resets your computer.
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:34 AM (Merged)
Tiny
KSO
  • MEMBER
  • 2 POSTS
Disconnect the battery and let it set for about 5 to 10 minutes I had that same problem a couple years back so it will probably work for you to.
Was this
answer
helpful?
Yes
No
Wednesday, December 23rd, 2020 AT 10:34 AM (Merged)

Please login or register to post a reply.

Sponsored links