My engine stalls at idle?

Tiny
KRIZNAD
  • MEMBER
  • 1 POST
  • 1984 CHEVROLET TRUCK
  • 6 CYL
  • 2WD
  • AUTOMATIC
  • 134,000 MILES
My 84 chevy c10 with 250 ci, dosen't want to idle in gear. It will run as long as I hold the gas a little. It idles rough out of gear but will stay running.
Was this
answer
helpful?
Yes
No
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)
Tiny
CHAMPION843
  • MEMBER
  • 4 POSTS
Check your timing, if your time is right then try your fuel to air ratio. Sometimes you have to readjust after making a switch of gasoline types if you go from high quality to a lower one.
Was this
answer
helpful?
Yes
No
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
It sounds like you need a tune up especially due to the rough running at idle. Or you have a vacuum leak or valve bad.
Was this
answer
helpful?
Yes
No
+1
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)
Tiny
VEGASMSTRJ
  • MEMBER
  • 50 POSTS
Thanks! That would make sense because I have alot of white smoke out the back. Tells me its not burning right. I'll check that out.
Was this
answer
helpful?
Yes
No
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)
Tiny
P.MILLS25
  • MEMBER
  • 1 POST
  • 1977 CHEVROLET TRUCK
Engine Performance problem
1977 Chevy Truck Two Wheel Drive Automatic

I have a 1977 chevy p/u with a 305 engine. It's been sitting since it over heated with my son a few months back. I fixed the problem with the over heating & I had to adjust the idle. I finally got it to idle without stalling, but now it stalls when you put it in gear. Replaced the gas pump, rebulit the carb. & Made sure no vac. Leaks, didn't help. PLEASE HELP!
Was this
answer
helpful?
Yes
No
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)
Tiny
DR LOOT
  • MECHANIC
  • 2,311 POSTS
It sounds to me like a vacuum leak, how did you check it for a vacuum leak? This is what I want you to do, remove the air cleaner with the engine running take the chock flap and slowly close at shut if the engine speeds up While you are closing it, you have a vacuum leak, let me know what happens so I can think of something else.
Was this
answer
helpful?
Yes
No
+1
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)
Tiny
HARMON HANSEN
  • MEMBER
  • 1 POST
  • 1976 CHEVROLET TRUCK
Engine Mechanical problem
1976 Chevy Truck V8 Two Wheel Drive Automatic *?* Miles

Engine stalls when it's put in gear, Idle just drops off &dies. It will start with a fairly fast idle then 'regulate' but when brake is applied and it's put in gear it dies.I think it's a 350 with a t/h400, Holley 4bbl. 76 towing special[came w/454 +xtras] seems like it would be something that I've dealt with but? Thank you.
Was this
answer
helpful?
Yes
No
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)
Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
Check the initial choke and fast idle cam adjustment-if okay-also check for vacuum leak at the brake hose and booster-recheck the ignition timing and A/F mix and curb idle speed-
Was this
answer
helpful?
Yes
No
Wednesday, November 25th, 2020 AT 8:21 AM (Merged)

Please login or register to post a reply.

Sponsored links