Engine misfire?

Tiny
SERVICE WRITER
  • MECHANIC
  • 9,123 POSTS
With all due respect I am still not convinced of a performance problem. I'll give what input you like as best I can.

I assume the mounts are good on the engine and tranny?
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
SHAVIL
  • MEMBER
  • 1 POST
  • 2000 TOYOTA COROLLA
  • 4 CYL
  • FWD
  • MANUAL
  • 180,000 MILES
Hi, I have a toyota corolla RXI. I recently changed my car VVT pulley. Had a reputable mechanic do it for me. After that change my car seems to have an unusual star up after a long drive. When engine is cold or warm its starts up normal but after about 10 minutes of driving the problem would occurr, I switch it off for 3 minutes and decide to start it and it gives a missing like start up, its not severe missing but not the normal start up. Just few gentle revs and the car is fine thereafter. No smoke puffs out from the exhaust. Car goes fine otherwise. Car has a 63 mil exhaust and no engine mods. Car does not miss when driving. What could be the problem?
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
DMK_RXI
  • MEMBER
  • 1 POST
HI I have the same problem with my blacktop 20v. Have you sorted out thre problem yet I am still looking for a solution
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
JEROMY1998
  • MEMBER
  • 4 POSTS
  • 2000 TOYOTA COROLLA
Electrical problem
2000 Toyota Corolla 4 cyl Front Wheel Drive Automatic 129xxx miles

It really just started missing out on my way home yesterday. I took it to the local AutoZone for them to run diagnostics, and it came up "Cylinder 1 Misfire". I changed the plugs, which were in pretty rough shape. However, this did not fix the problem. I also, while the car was running, unplugged each Coil, one at a time. All four coils, when unplugged, caused the car to die. So it appears as though the coils are working. Anyone have any insight on what may be my problem? I have a fairly long commute to work each day, and would hate to have to drive it like this. Thanks
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
STEVEW84
  • MECHANIC
  • 673 POSTS
This is what I would do. Take the number 1 coil and move it to number 2. Clear the code(you can disconnect the battery to do this, but it is better to do it with a scanner). Then drive it until the check engine light comes back on then take it to autozone to have the code checked again. If it says p0302(#2 misfire) then you have a bad coil. If not then you have another issue. Probably bad fuel injector, inj. Control, spark control, etc. Number 1 cyinder is the cylinder closest to the crankshaft pulley.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
SCOTT KAYSER
  • MEMBER
  • 3 POSTS
  • 2000 TOYOTA COROLLA
  • 4 CYL
  • 2WD
  • 260,000 MILES
Misfire on cylinder three: changed all plugs, installed new coil pack on cylinder three, swapped cylinder three injector with another cylinder. Codes never changed still misfire on cylinder three. If I unplug electrical connection to cylinder three injector, no change to rough running engine, do the same to other cylinders and engine almost dies. If I unplug electrical connection to cylinder three coil pack then engine dies. Idles a little rough but really shakes under load. Check engine light blinks at about forty mph but stops below that or when idling in park. Why would unplugging coil pack on cylinder three kill engine but when I unplug cylinder three injector there is virtually no change in how the engine is running?
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Really does not make much sense why it would do that. Have you performed a Compression test yet? Sounds like you might have low compression on number three cylinder.
Was this
answer
helpful?
Yes
No
+1
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
SCOTT KAYSER
  • MEMBER
  • 3 POSTS
No I have not. Never have done that. This may be one for the true mechanics.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
It is easy to do a compression test, rent a compression tester from auto zone. Then all you do is remove all the spark plugs screw the tester in hold the gas pedal to the floor and crank the engine like ten revolutions and write down all the cylinder readings.
Was this
answer
helpful?
Yes
No
+1
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
SCOTT KAYSER
  • MEMBER
  • 3 POSTS
Thanks, I will try that tomorrow if I get the chance.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Okay, keep me posted.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
JEROMY1998
  • MEMBER
  • 4 POSTS
  • 2000 TOYOTA COROLLA
  • 4 CYL
  • FWD
  • AUTOMATIC
  • 135,000 MILES
My 2000 corolla is missing badly. I have taken it to a mechanic, and all he said is it was running to "good" to be anything major. However, today, it started missing even worse, and barely makes it up a hill. Whenever I try accelerating up a hill, it makes a "rattling" noise; sounding like it's coming from the engine. What in the world is that? I have checked the Coil-packs, has no oil in antifreeze, and no oil on spark plugs. Please help in any way you can.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
STEVEW84
  • MECHANIC
  • 673 POSTS
How did you check the coil packs? If its misfiring then your Check engine light is on. What is the code?
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
MMPRINCE4000
  • MECHANIC
  • 8,548 POSTS
The rattling noise is pre-ignition and can cause severe engine damage if not repaired.

You might want to find another mechanic.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
JEROMY1998
  • MEMBER
  • 4 POSTS
Thanks, but what exactly is "pre-ignition"? And how is it fixed?
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
JEROMY1998
  • MEMBER
  • 4 POSTS
I checked the coil packs by first starting the car. Then, one by one, I disconnected them; all four of them seemed to be working because as I disconnected them, the car would start to die. And it was the same with all four. The code said "cylinder 1 misfire".
Was this
answer
helpful?
Yes
No
-1
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
MMPRINCE4000
  • MECHANIC
  • 8,548 POSTS
Pre-ignition is where the cylinder fires before the piston reaches TDC, it is usually a timing issue, crank sensor, cam sensor, timing chain, PCM.

If you have a cylinder misfire code, then you first want to check the plug on that cylinder.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:31 AM (Merged)
Tiny
LILYVINE RESOURCES
  • MEMBER
  • 1 POST
  • 2000 TOYOTA COROLLA
  • 1.5L
  • 4 CYL
  • 2WD
  • AUTOMATIC
  • 223,870 MILES
My car jerks each time l turn the ignition on and until the car stops. Would drive or go with a reverse, because it will go off and this has eventually lead to hard starting almost every time.
Once the jerking stops the car will drive perfectly, but I am not comfortable with the situation.
What could wrong with the car?
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:32 AM (Merged)
Tiny
MHPAUTOS
  • MECHANIC
  • 31,937 POSTS
You need to be checking for a problem with a spark plug, coil or a vacuum leak, get a scan done and see if any codes are for a misfire. If so it should indicate a cylinder at fault or a random misfire. There can be other causes so a code scan will help with the diagnoses, so get this done and post back any codes retrieved.
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:32 AM (Merged)
Tiny
RENEE L
  • ADMIN
  • 1,260 POSTS
Hello LILYVINE RESOURCES,

If you decide you would like to conduct the scan yourself here is a link to an article from this site that features written step by step instructions and pictures explaining how to do the scan yourself. Also, I have included a link to our YouTube channel with a how to video on code scanning.

This is applicable even if your check engine light is not on.

Most scanners are inexpensive to purchase, you can purchase one online from sites like Amazon.com

https://www.2carpros.com/articles/checking-a-service-engine-soon-or-check-engine-light-on-or-flashing

https://youtu.be/YV3TRZwer8k

Once you have the codes please get back to us with the code number(s) so that we can further assist you. We are always happy to help.

Thank you for visiting 2CarPros.com.

Kindest regards,

Renee
Admin
Was this
answer
helpful?
Yes
No
Monday, August 10th, 2020 AT 10:32 AM (Merged)

Please login or register to post a reply.

Sponsored links