1996 Cadillac Deville 4.9L

Tiny
WISCONSINJIMMY
  • MEMBER
  • 14 POSTS
No I did not cut anything off, I bought the car this way and I am unbolting all the wiring in the engine bay pulling it through the firewall and then I will reinstall the wiring so it is easier and safer to work around, sawzall makes jagged edges, look at the photo. I spent most of the day working at reverse engineering the dash to make sure all wires and looms came apart with no damage, you can see in the photo where the wires are cut and the same for the right side.
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 1:45 AM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,761 POSTS
I know it wasn't you that did it. There was a fuse box in the trunk.
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 1:48 AM
Tiny
WISCONSINJIMMY
  • MEMBER
  • 14 POSTS
That is what my triker friend said so now I must work around the problem which is not insurmountable just need to get a good schematic
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 1:50 AM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,761 POSTS
No, you need the missing harness to the back to try to splice back in. That is your only hope.
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 1:52 AM
Tiny
WISCONSINJIMMY
  • MEMBER
  • 14 POSTS
Well that helps me make the decision to send this to the scrap yard and save me a lot of time. Hey guys thanks for the help and ideas but I think if it is not raining tomorrow I will load it on the trailer.
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 1:55 AM
Tiny
CADIEMAN
  • MECHANIC
  • 3,544 POSTS
If there is no fuse panel under the dash it has to be in the rear. The 2 computers 1 is the ecm 1 is the bcm. Youll have a hard time pulling a full rear harness at the junk yard. Best bet is to have them pull it. And splice it in with shrink rap connectors. If u remove any harnesses u need to put masking tap on the wireing and write what componit it goes to. Allways label gl
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 1:13 PM
Tiny
WISCONSINJIMMY
  • MEMBER
  • 14 POSTS
Well the car is on its way to the salvage yard as it was going to be to much work and scrap is at $200. A ton and cash is good.
Jim
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 8:49 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,761 POSTS
Wish you had shown that picture first. It would have made all this much easier.
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 8:56 PM
Tiny
WISCONSINJIMMY
  • MEMBER
  • 14 POSTS
I posted a photo of it at the top of the post, when I was told it was a bit on the impossible side that told me to scrap it.
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 8:59 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,761 POSTS
You're right. I missed that.
Was this
answer
helpful?
Yes
No
Thursday, April 7th, 2011 AT 10:30 PM

Please login or register to post a reply.

Sponsored links