SPONSORED LINKS

Replacing serpentine belt

Tiny
WANDRNSTAR
  • MEMBER
  • 2004 FORD F-250
  • V8
  • 4WD
  • AUTOMATIC
  • 61,890 MILES
I have to replace the altenator. Taking it off was easy. Now I am trying to get the new one on and put the serpentine belt back on. The engine is so crowded I cannot find the tensioner. Where is it on this engine? 6.0L Turbo deisel.

Thanks,
Vin
SPONSORED LINKS
Tuesday, December 18th, 2007 AT 5:38 PM

16 Replies

Tiny
BLACKOP555
  • MECHANIC
  • 10,371 POSTS
Here is a guide to help you step by step with instructions in the diagrams below to show you how on your car.

https://www.2carpros.com/articles/replace-serpentine-belt

and

https://www.2carpros.com/diagrams/ford/pickup/2004

Please let us know if you need anything else to get the problem fixed.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Tuesday, December 18th, 2007 AT 7:25 PM
Tiny
FLEXY5
  • MECHANIC
  • 512 POSTS
"By the book" you are suppose to remove the upper fan shroud. On the older 6.0 you had to cut it at a certain groove on either side of the shroud (BRILLIANT!). However, at the dealership, we implemented a shortcut. It's not the greatest way to do it, but it saves 2 hours of time. The belt tensioner is on the passenger side, towards the bottom/middle of the engine cover. If you slide a prybar down, you can push down on the tensioner. DO NOT PRY AGAINST OTHER THINGS! It may take two people to get the job done, but we were able to change a belt on a 6.0 in about 6 minutes flat. Let me know if you have any questions.
Was this
answer
helpful?
Yes
No
Tuesday, December 18th, 2007 AT 9:18 PM
Tiny
PGANGI
  • MEMBER
  • 3 POSTS
  • 2003 FORD F-250
  • V8
  • 4WD
  • AUTOMATIC
  • 160,000 MILES
How to remove drive belt. I cannont get room to put tool on tensioner. The clip lock on the tensioner is not working
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
MERLIN2021
  • MECHANIC
  • 17,250 POSTS
I use two combination wrenches hooked together to get enough leverage to hold the tensioner while I slip the belt off, and back on.


https://www.2carpros.com/forum/automotive_pictures/62217_wrenches_12.jpg

Was this
answer
helpful?
Yes
No
-1
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
PGANGI
  • MEMBER
  • 3 POSTS
Thank you for the info. Could you please answer the question?I already know the answer, another site was able to help me. I just want to get my moneys worth.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
MERLIN2021
  • MECHANIC
  • 17,250 POSTS
Tis is how I do it if the room is tight, on a rear drive like yours, it's fairly simple. I thought I did answer your question, so I don';t understand the "getting your money's worth" Statement. Serp belt and tensioner is basic stuff, so what is the problem getting the belt off? No leverage? Not accessible? All you do is turn the bolt on the tensioner with some force, this will unwind the tension and allow the removal of the belt. To install it, there is a tool available to put the belt on the lower pulleys if you cant reach them, it's a thin bar with a hook on it.
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
PGANGI
  • MEMBER
  • 3 POSTS
Never mind. The special tool will not work since the 1/2 drive slot is recessed. So you have to use a 3/8 to 1/2 adapter with a ratchet and a piece of pipe on the ratchet for leverage and it fits in the tight spot on the vehicle I described. This was the answer to the question not here is a picture of how to put 2 wrenches together to gain more leverage. On top of that you never addressed the clip on the tensioner on this vehicle, which by the way is a short cut, if it works, so that yo do not have to uses any wrencehses at all. Now you can answer the next guy's question that is the same as mine with a bit more intelligence.
Later
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
MERLIN2021
  • MECHANIC
  • 17,250 POSTS
I have never had to use pipe to change a belt. And you can put a wrench on the bolt on the tensioner pulley. Good luck with your intelligent answer.
Was this
answer
helpful?
Yes
No
-1
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
2CP-ARCHIVES
  • MEMBER
  • 4,540 POSTS
  • 2003 FORD F-250
  • 60,000 MILES
How do I replace a serpentine belt on a F250 6.0L Diesel truck?
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
JDL
  • MECHANIC
  • 16,098 POSTS
Note the diagram for single alternator serpentine belt. See #8 that is the tensioner, looks like a drive cavity, don't know the size, 3/8/or a 1/2. Use a long handle rachet or breaker-over, whatever is easier, push to release tension.
Image (Click to make bigger)
Thumb
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
WAYNE H
  • MEMBER
  • 1 POST
  • 2001 FORD F-250
  • V10
  • 2WD
  • AUTOMATIC
  • 79,000 MILES
How do I change my serpentine belt for my "2001" Ford F250
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
JACOBANDNICKOLAS
  • MECHANIC
  • 109,805 POSTS
There is an automatic tensionier that needs released. Once you turn it, the belt will come off. Go to our homepage under the DIY section. Go to belts and it will provide the belt diagram you need for your vehicle.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
JACK FRY
  • MEMBER
  • 2 POSTS
  • 1996 FORD F-250
  • 7.3L
  • 4WD
  • AUTOMATIC
  • 111,000 MILES
What size socket goes on the tensioner pulley to use the belt removal tool?
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
CARADIODOC
  • MECHANIC
  • 33,889 POSTS
It should be a 15mm. But we just look at what type of tool is needed, and if it's an open-end wrench or socket, we try a few to find the right one. Some replacements use a square drive, usually 1/2", as found on the end of a ratchet or breaker bar.

Here is a guide to help you see what you are in for when doing the job.

https://www.2carpros.com/articles/replace-serpentine-belt

and

https://www.2carpros.com/diagrams/ford/pickup/1996

Please let us know if you need anything else to get the problem fixed.

Cheers
Was this
answer
helpful?
Yes
No
+2
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
JACK FRY
  • MEMBER
  • 2 POSTS
Thank you I got the job done the links really helped!
Was this
answer
helpful?
Yes
No
Monday, January 25th, 2021 AT 7:38 PM (Merged)
Tiny
CARADIODOC
  • MECHANIC
  • 33,889 POSTS
Good to hear, please use 2CarPros anytime we are here to help.

Cheers
Was this
answer
helpful?
Yes
No
+1
Monday, January 25th, 2021 AT 7:38 PM (Merged)

Please login or register to post a reply.

Related Serpentine Belt Replace/Remove Content

Serpentine Belt Replacement Ford
VIDEO
Serpentine Belt Replacement Ford
Instructional repair video
Serpentine Belt Replacement
GUIDE
Serpentine Belt Replacement
Need to change your serpentine belt? This is an easy job in most cases. There are several names used to describe a serpentine belt, including: drive belt, poly-v belt, multi...
VIEW MORE

Sponsored links