SPONSORED LINKS

Vacuum from the transducer to the EGR valve

Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Your welcome thats what were her for helpng people with there cars. Please keep me posted if your car is running good acting up again.I had my sisters saturn do a simlar thing setting a map code moved some wires around it never happened again. Iam not complaining about that one lol I have enough family members cars to fix already lol. Also please tell all your friends about us.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Saturday, August 11th, 2012 AT 9:57 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
I will keep you posted and I will let my friends know about carpros im just thankiful that I know how to work on cars a well but im not good when it comes to the newer cars and trucks give me a 350 chevy small block and it will run and thanks saturnteck9
Was this
answer
helpful?
Yes
No
Saturday, August 11th, 2012 AT 10:02 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Anytime thats what here for.
Was this
answer
helpful?
Yes
No
Saturday, August 11th, 2012 AT 10:05 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
Saturntech9 the car was running fine tell today and its doing the samething stalling when I start it. Im so angry right now and I did was change the right side lower control arm because the ball joint and I went to start the car and its stalling dont know what to do anymore
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 8:19 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Do you have any codes?If so what are the exact code nunbers you have?
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 9:03 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
Engine light is on but no codes at all on the scanner
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 9:07 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
If the check engine light is on while the engine is running it should have codes in the computer.
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 9:18 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
It doesnt I have tried a few time and there is no code. I have started it and tried to get a code and I have did it with just the key turned on
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 9:24 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
What is the map sensor voltage key in the run position engine off?Also with the engine idling?
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 10:06 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
Well I changed the map sensor and now its fine what could be going on with this car. It acts up and I changed it and it does the samething so I change it again and its fine and then it will happen again. Could it be a broking wire or bad pcm
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 10:11 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
Voltage to the pcm or the power voltage going in to the sensor
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 10:13 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
I would say you have a wire going to the map sensor thats close the map sensor that is bad. Probably the copper wire is broken inside the insulation. To me thats the only thing that makes sense at this point.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 10:17 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
What do you mean by close the map sensor
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 10:31 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
I missed a word close to the map sensor. Meaning when you unplug or plug in the map sensor connector you disturb the bad wire.
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 10:40 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
I understand now. One I mit have a bad wire or two I have a bad plug. So what you are saying is test the wires when I move them around and test that plug to see it one breaks the connection
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 10:44 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Heres what I would do put the key in the run position engine off watch the map sensor volts while moving the wired connector etc around.
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 11:03 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
Ok I will go do that now
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 11:04 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Keep me posted.
Was this
answer
helpful?
Yes
No
Saturday, August 18th, 2012 AT 11:30 PM
Tiny
LEAVITT
  • MEMBER
  • 29 POSTS
Ok I have checked the connection at the sensor and moved around the wires and everything seems tobe fine with the connection and I also checked the voits the power wire was 5 volts and the signal wire was 4.5 volts but im wondering about the ground wire that goes to the sensor
Was this
answer
helpful?
Yes
No
Sunday, August 19th, 2012 AT 11:02 PM
Tiny
SATURNTECH9
  • MECHANIC
  • 30,869 POSTS
Are these readings with the map sensor plugged in?
Was this
answer
helpful?
Yes
No
Monday, August 20th, 2012 AT 3:35 PM

Please login or register to post a reply.

Related EGR Valve Replace/Remove Content

Sponsored links