Is sealant needed when replacing valve cover gaskets

Tiny
CHEVY__88
  • MEMBER
  • 2001 LINCOLN TOWN CAR
  • V8
  • AUTOMATIC
  • 118,000 MILES
Do I need to use any sealant when replacing brand new valve cover gaskets?
Saturday, February 24th, 2018 AT 11:02 AM

13 Replies

Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Good afternoon.

No, do not use any sealant on new gaskets.

Roy
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 11:38 AM
Tiny
CHEVY__88
  • MEMBER
  • 95 POSTS
Not even around the mating joints timing cover/cylinder head?
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 12:19 PM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
When tightened down and torqued, the gasket will fill in the gap.

Roy
Was this
answer
helpful?
Yes
No
+1
Saturday, February 24th, 2018 AT 2:37 PM
Tiny
CHEVY__88
  • MEMBER
  • 95 POSTS
Okay, so do you usually have to take the brake booster off? Seen quite a few videos where they do and they do not.
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 2:41 PM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Yes, I do. I make it easy on myself. It takes longer but is easier with it off.

Roy
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 2:42 PM
Tiny
CHEVY__88
  • MEMBER
  • 95 POSTS
What about the passenger side? Anything extra that needs to come off?
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 4:13 PM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
No, just a matter of moving as much out of the way as possible. It comes up easily.
Be careful of the wiring.

Roy
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 4:29 PM
Tiny
CHEVY__88
  • MEMBER
  • 95 POSTS
How do I know if my car is equipped with ABS? The manual was saying not to remove the master cylinder if it is equipped. To let a professional do it.
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 6:55 PM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
You would have a yellow ABS light on the dash when you turn on the key that would say ABS.

You do not remove the master cylinder, just unbolt it and pull it forward and over with the lines attached.

Roy
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 6:59 PM
Tiny
CHEVY__88
  • MEMBER
  • 95 POSTS
Okay, yeah I only need just a little bit more room. Tried taking it off without messing with that stuff.
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 7:03 PM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Take your time.
It is always so close. Just do not damage anything.

Roy
Was this
answer
helpful?
Yes
No
Saturday, February 24th, 2018 AT 7:09 PM
Tiny
CHEVY__88
  • MEMBER
  • 95 POSTS
Is there any tricks to it? I just cannot seem to get either one off. I loosened the master cylinder.
Was this
answer
helpful?
Yes
No
Sunday, February 25th, 2018 AT 10:46 AM
Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
Did you remove it? Then you need to remove the booster. Did you do that?

Roy
Was this
answer
helpful?
Yes
No
Sunday, February 25th, 2018 AT 3:06 PM

Please login or register to post a reply.

Sponsored links