Advertisement
Advertisement

2003 Chevy Suburban Rumbling Noise when Decelerating

92,000 MILES • V8 • 2WD • AUTOMATIC
Avatar
MBERGM1
  • MEMBER
  • 4 POSTS
When driving at +30 MPH and I let off the accelerator, I hear a rumbling noise that sounds like I'm driving on those wake-up grooves on the side of the road though not as loud or vibrating. Any clues?
Feb 16, 2010 at 5:05 AM
Avatar
JACOBANDNICKOLAS
  • ✓Experienced Mechanic
  • 110,248 POSTS
It sounds like a bearing noisie. Can you tell aprox where it is coming from on the vehicle?
Feb 16, 2010 at 5:30 AM
Advertisement
Avatar
MBERGM1
  • MEMBER
  • 4 POSTS
The sound diminished when I listened outside (window rolled down) so I would imagine passenger side. Is there something I could check to confirm? Would you be able to hear the noise when the car passes by?
Feb 16, 2010 at 6:18 AM
Avatar
JACOBANDNICKOLAS
  • ✓Experienced Mechanic
  • 110,248 POSTS
Try a little test. While driving straight down the road, (make sure no one is coming toward you) weave left to right just enough to see if the sound chances. Please don't swirve hard enough to cause an accident.

Let me know what happens. If there is a change in sound, my first guess is a wheel bearing. If there is no change, we need to check transfer case and differential bearings for play.

Joe
Feb 16, 2010 at 8:29 AM
Avatar
MBERGM1
  • MEMBER
  • 4 POSTS
There might have been a slight change but I cannot be for sure. I did notice when I was going through a curve in the road, the noise came and went. The thing is, it only happens when I am decelerating after reaching 35-40mph or more. I didn't try the curve from the other direction. Should I? What are the checks for the other two issues you mentioned?
Feb 16, 2010 at 10:32 AM
Avatar
JACOBANDNICKOLAS
  • ✓Experienced Mechanic
  • 110,248 POSTS
If the sound changed when turning, chances are you have a bad wheel bearing.

As far as the other test, you need to get under the vehicle and check for play where the drive shafts connect to the differential and transmission. If you try that, make sure the vehicle is in neutral, the park brake on securly, and block the wheels so the vehicle can't move. It needs to be in neutral so there is no tension on the drive shafts.

Let me know what you find. Also, when turning, if you tell me what direction turn made the noise go away, I'll tell you on what side the wheel bearing is bad.

Let me know.
Joe
Feb 17, 2010 at 1:49 AM
Avatar
MBERGM1
  • MEMBER
  • 4 POSTS
Well, I took it into my local shop... It turned out to be the U-joints. Thanks for your help.
Feb 17, 2010 at 9:57 AM
Avatar
JACOBANDNICKOLAS
  • ✓Experienced Mechanic
  • 110,248 POSTS
I'm glad you found it. We were close, if you would have checked the driveshaft for bearing problems, you would have found it. Next time we'll get it.

Regardless, thank you for using 2carpros.com, we appreciate your business.

Thanks again, and let us know if you have trouble in the future.

Joe
Feb 17, 2010 at 5:02 PM
Add a reply
Join 2CarPros for free, one of the most advanced car repair communities on the internet. From first-time drivers to seasoned mechanics, everyone is welcome to reply, share details, and get better answers. You can add a temporary image or video first; uploads are limited to 20 MB.

Frequently Asked Problems for This Vehicle

Advertisement