2000 Chevy Silverado truck starts then stops

Tiny
ROCKLOS1
  • MEMBER
  • 2000 CHEVROLET SILVERADO
  • V8
  • 4WD
  • AUTOMATIC
  • 155,000 MILES
Truck starts but shuts off, ive replace fuel pump a few month ago right now its doing 55-60psi key on, changed the crank position sensor, fuel filter, regulator, still nothing, no codes on scanning computer. Need help to get going?
Monday, July 7th, 2008 AT 2:21 PM

12 Replies

Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
Try feeding it with carb cleaner continuously does it continue to run if so test the oil pressure sending unit-
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 3:03 PM
Tiny
ROCKLOS1
  • MEMBER
  • 6 POSTS
It does run with staring fluid or carb cleaner, I also was told to check the injector for a pulse and nothing there.
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 4:49 PM
Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
Could be that the computer is not receiving the ignition reference signal therefore its not energizing the injector/s or a problem with drivers in the computer or power to the injector/s-
Was this
answer
helpful?
Yes
No
-1
Monday, July 7th, 2008 AT 6:21 PM
Tiny
ROCKLOS1
  • MEMBER
  • 6 POSTS
Thanks for the help your giving me, I just picked up a pcm from a bone yard and still the same, starts and stops?
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 6:56 PM
Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
Try this use direct power from the battery to the fuel pump connector gray wire-
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 7:06 PM
Tiny
ROCKLOS1
  • MEMBER
  • 6 POSTS
Is there any other place to catch that grey wire or do I have to tie in at the fuel tank.
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 7:58 PM
Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
You can power it thru the fuel pump terminal of the diagnostic connector if it has the terminal
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 8:52 PM
Tiny
ROCKLOS1
  • MEMBER
  • 6 POSTS
Ok I powered it though the main fuse panel theres a prim connector and added the 12 volt heard it humming and cranked the key a few time and still nothing, I do have a pressure gauge on the rails and its doing 58 psi.
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 9:05 PM
Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
Crank engine over while listening to the injector/s are they clicking meaning its pulsing
Was this
answer
helpful?
Yes
No
Monday, July 7th, 2008 AT 10:18 PM
Tiny
ROCKLOS1
  • MEMBER
  • 6 POSTS
I put I test light to it and no flashing.
Was this
answer
helpful?
Yes
No
Tuesday, July 8th, 2008 AT 4:38 AM
Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
Did you check injector A and B fuses 15amps, also check the camshaft position sensor in the distributor this is the one that synchronizes the injectors-
Was this
answer
helpful?
Yes
No
Tuesday, July 8th, 2008 AT 3:48 PM
Tiny
ROCKLOS1
  • MEMBER
  • 6 POSTS
Fuses good, truck is 2000 and it doesnt have a distributor.
Was this
answer
helpful?
Yes
No
Tuesday, July 8th, 2008 AT 5:02 PM

Please login or register to post a reply.

Sponsored links