ENGINE IDLING SPEED IS FAST

Tiny
KRIPALU
  • MEMBER
  • 2011 NISSAN WINGROAD
  • 25,000 MILES
HOW CAN YOU DO A "VOLUME AIR RE-LEARN" PROCEDURE ON A VEHICLE () USING A LAUNCH X431 MASTER SCANNER? THE VEHICLE ENGINE IDLING SPEED IS FAST AND I WANT TO DECREASE THIS SPEED.

MANY THANKS
Monday, May 28th, 2012 AT 4:09 AM

7 Replies

Tiny
ASEMASTER6371
  • MECHANIC
  • 52,797 POSTS
It is done through a scan tool. Unless you have a scan tool, you will need a shop to perform this for you. It will not lower the idle, just return the idle to the factory setting

Roy
Was this
answer
helpful?
Yes
No
-1
Monday, May 28th, 2012 AT 11:19 AM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
Either you use the Nissan Consult III or you would have to manually perform Idle Air Volume Learning.

X431 is not required.
Was this
answer
helpful?
Yes
No
-1
Monday, May 28th, 2012 AT 3:31 PM
Tiny
KRIPALU
  • MEMBER
  • 16 POSTS
What are the steps to manually perform the Idle Air Volume Learning?
Was this
answer
helpful?
Yes
No
+1
Monday, May 28th, 2012 AT 9:11 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,761 POSTS
Why would you try to mess with a brand new vehicle that is under warranty? The idle speed is controlled by the computer and you cannot lower it. The relearn procedures are performed when a new part is installed so the computer can calibrate to it.
Was this
answer
helpful?
Yes
No
-1
Monday, May 28th, 2012 AT 9:50 PM
Tiny
KRIPALU
  • MEMBER
  • 16 POSTS
The vehicle was purchased from Japan and it is not under warranty. It is idling fast and I just want to lower the speed to its original factory setting.
Was this
answer
helpful?
Yes
No
Monday, May 28th, 2012 AT 10:14 PM
Tiny
WRENCHTECH
  • MECHANIC
  • 20,761 POSTS
There is no adjustment. The computer is programmed to maintain the specs it was programmed to and you can't change that.
Was this
answer
helpful?
Yes
No
-1
Monday, May 28th, 2012 AT 10:32 PM
Tiny
KHLOW2008
  • MECHANIC
  • 41,814 POSTS
Here are the procedures.

NOTE:
It is better to count the time accurately with a clock.

It is impossible to switch the diagnostic mode when an accelerator pedal position sensor circuit has a malfunction.

1. Perform "ACCELERATOR PEDAL RELEASED POSITION LEARNING".

2. Perform "THROTTLE VALVE CLOSED POSITION LEARNING".

3. Start engine and warm it up to normal operating temperature.

4. Check that all items listed under the topic PREPARATION are in good order.

5. Turn ignition switch OFF and wait at least 10 seconds.

6. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.

7. Repeat the following procedure quickly five times within 5 seconds.
A. Fully depress the accelerator pedal.
B. Fully release the accelerator pedal.

8. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 20 seconds until the MIL stops blinking and turned ON.

9. Fully release the accelerator pedal within 3 seconds after the MIL turned ON.

10. Start engine and let it idle.

11. Wait 20 seconds.

12. Rev up the engine two or three times and make sure that idle speed and ignition timing are within the specifications.

13. If idle speed and ignition timing are not within the specification, Idle Air Volume Learning will not be carried out successfully.

ACCELERATOR PEDAL RELEASED POSITION LEARNING

DESCRIPTION

Accelerator Pedal Released Position Learning is an operation to learn the fully released position of the accelerator pedal by monitoring the accelerator pedal position sensor output signal. It must be performed each time harness connector of accelerator
pedal position sensor or ECM is disconnected.

OPERATION PROCEDURE

1. Make sure that accelerator pedal is fully released.

2. Turn ignition switch ON and wait at least 2 seconds.

3. Turn ignition switch OFF and wait at least 10 seconds.

4. Turn ignition switch ON and wait at least 2 seconds.

5. Turn ignition switch OFF and wait at least 10 seconds.

THROTTLE VALVE CLOSED POSITION LEARNING

DESCRIPTION

Throttle Valve Closed Position Learning is an operation to learn the fully closed position of the throttle valve by monitoring the throttle position sensor output signal. It must be performed each time harness connector of electric throttle control actuator or
ECM is disconnected.

OPERATION PROCEDURE

1. Make sure that accelerator pedal is fully released.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

Make sure that throttle valve moves during above 10 seconds by confirming the operating sound.
Was this
answer
helpful?
Yes
No
Tuesday, May 29th, 2012 AT 5:48 PM

Please login or register to post a reply.

Sponsored links