Blower stopped working

POPPOP101

MEMBER
2006 SUZUKI VITARA
136,000 MILES

The blower stopped working. I Checked the fuses and they are good Was going to try to see if I need to replace the transistor but do not know where it is located or how to replace. They told me that there was a recall on the blowers for the 06 models but I am not the original owner. So trying to repair on my own. Unless it might be the switch itself. Need all the help I can get.

1 Reply

JACOBANDNICKOLAS

MECHANIC
109,867 POSTS

Hi,

Does the blower motor work on any speed? If not, I need you to check fuse 32 in fuse box 3. See pic 1. In addition to checking the fuse, confirm there is power to it. Here is a link you may find helpful:

https://www.2carpros.com/articles/how-to-check-a-car-fuse

Next, check the blower motor relay. Here are the directions for testing it. Do this next.

___________________________

2006 Suzuki Truck Grand Vitara 2WD V6-2.7L
Component Tests and General Diagnostics
Vehicle Heating and Air Conditioning Blower Motor Relay Testing and Inspection Component Tests and General Diagnostics
COMPONENT TESTS AND GENERAL DIAGNOSTICS
BLOWER MOTOR RELAY INSPECTION

1. Disconnect negative (-) cable at battery.
2. Remove blower motor relay (1) from vehicle.
3. Check that there is no continuity between terminal "c" and "d". If there is continuity, replace relay.

See pic 2

4. Connect battery positive (+) terminal to terminal "b" of relay.
Connect battery negative (-) terminal to terminal "a" of relay.
Check continuity between terminal "c" and "d".
If there is no continuity when relay is connected to the battery, replace relay.

________________________

If both are good, then you should check to see if there is power to the motor itself. If there isn't, suspect the blower motor resister is bad. If there is power, suspect the motor itself it bad.

_______________________

Here are the directions for replacing the blower motor.

2006 Suzuki Truck Grand Vitara 2WD V6-2.7L
Component Tests and General Diagnostics
Vehicle Heating and Air Conditioning Blower Motor Relay Testing and Inspection Component Tests and General Diagnostics
COMPONENT TESTS AND GENERAL DIAGNOSTICS
BLOWER MOTOR RELAY INSPECTION

1. Disconnect negative (-) cable at battery.
2. Remove blower motor relay (1) from vehicle.
3. Check that there is no continuity between terminal "c" and "d". If there is continuity, replace relay.

see pic 3t

4. Connect battery positive (+) terminal to terminal "b" of relay.
Connect battery negative (-) terminal to terminal "a" of relay.
Check continuity between terminal "c" and "d".
If there is no continuity when relay is connected to the battery, replace relay.

_____________________________

Here are the directions for resister replacement:

____________________________

2006 Suzuki Truck Grand Vitara 2WD V6-2.7L
Procedures
Vehicle Heating and Air Conditioning Blower Motor Resistor Service and Repair Procedures
PROCEDURES
BLOWER MOTOR CONTROLLER REMOVAL AND INSTALLATION

Reference: Blower Unit and Heater Unit Components

Removal
1. Disconnect negative (-) cable at battery.
2. Disable air bag system referring to Disabling Air Bag System: Advanced Air Bag or Disabling Air Bag System: Except Advanced Air Bag.
3. Remove glove box.
4. Remove passenger lower member.
5. Disconnect blower motor controller coupler (3).

pic 4

6. Remove blower motor controller (1) by loosening its fastening screws (2).

Installation
Reference: Blower Motor Controller Inspection
1. Reverse removal procedure.
2. Enable air bag system referring to Enabling Air Bag System: Advanced Air Bag or Enabling Air Bag System: Except Advanced Air Bag.

______________________

Let me know if this helps or if you have other questions.

Take care,
Joe

Images (Click to make bigger)