where is the evap vent solenoid located on a 2004 chevy monte carlo ss? looking for picture or diagram...
Nov 11, 2012 at 11:11 PM
evap vent solenoid location
2004 CHEVROLET MONTE CARLO
ANONYMOUS
- MEMBER
- 1 POST
Advertisement
RASMATAZ
- ✓ASE Certified Mechanic
- 75,992 POSTS
-Evaporative Emission (EVAP) Canister Vent Solenoid Connector Behind left rear splash shield, in wheelwell.
Image (Click to enlarge)
Professional Diagram for 2CarPros Members
Click here to log in and view diagram.
Click here to log in and view diagram.
Nov 11, 2012 at 11:23 PM
need to know how to get to the r&r evap vent solenoid for a 2004 Chevy Monte Carlo SS
Dec 5, 2019 at 12:27 PM
(Merged)
ASEMASTER6371
- ✓ASE Certified Mechanic
- 52,796 POSTS
REMOVAL PROCEDURE
Raise and support the vehicle. Refer to Vehicle Lifting.
Disconnect the evaporative emission (EVAP) vent valve electrical connector (1).
Remove the EVAP vent valve bracket bolt.
Remove the vent hose (4) from the EVAP vent valve.
Remove the EVAP vent valve from the bracket (2).
INSTALLATION PROCEDURE
Install the EVAP vent valve to the bracket (2).
Install the vent hose (4) to the EVAP vent valve.
Install the EVAP vent valve and the bracket.
NOTE: Refer to Fastener Notice in Service Precautions.
Install the EVAP vent valve bracket bolt.
Tighten
Tighten the bolt to 10 N.m (89 lb in) .
Connect the EVAP vent valve electrical connector (1).
Lower the vehicle.
Raise and support the vehicle. Refer to Vehicle Lifting.
Disconnect the evaporative emission (EVAP) vent valve electrical connector (1).
Remove the EVAP vent valve bracket bolt.
Remove the vent hose (4) from the EVAP vent valve.
Remove the EVAP vent valve from the bracket (2).
INSTALLATION PROCEDURE
Install the EVAP vent valve to the bracket (2).
Install the vent hose (4) to the EVAP vent valve.
Install the EVAP vent valve and the bracket.
NOTE: Refer to Fastener Notice in Service Precautions.
Install the EVAP vent valve bracket bolt.
Tighten
Tighten the bolt to 10 N.m (89 lb in) .
Connect the EVAP vent valve electrical connector (1).
Lower the vehicle.
Dec 5, 2019 at 12:27 PM
(Merged)
Where is the Canister Purge Valve Solenoid located on a 2003 Monte Carlo SS?
Dec 5, 2019 at 12:27 PM
(Merged)
FACTORYJACK
- ✓ASE Certified Mechanic
- 4,159 POSTS
Emissions (EVAP) Canister Purge Solenoid (3.8L VIN K) is on top front of engine, near center of upper intake plenum. Here is a picture.
Dec 5, 2019 at 12:27 PM
(Merged)
how can i check it for proper operation?
Dec 5, 2019 at 12:27 PM
(Merged)
STRAILER
- ✓ASE Certified Mechanic
- 54,832 POSTS
Hey, SCARMECH
Remove the valve and then use two wires with a pigtail clips onto a battery 12 volt source. Next, touch the wires to the terminals inside the solenoid, you should hear a click which tells you it is working.
Remove the valve and then use two wires with a pigtail clips onto a battery 12 volt source. Next, touch the wires to the terminals inside the solenoid, you should hear a click which tells you it is working.
Dec 5, 2019 at 12:27 PM
(Merged)
2000 Chevy Monte Carlo 6 cyl Front Wheel Drive Automatic
where is it located/emission control sensor
where is it located/emission control sensor
Dec 5, 2019 at 12:27 PM
(Merged)
HMAC300
- ✓ASE Certified Mechanic
- 48,601 POSTS
it's a valve not a sensor. it's by the gas tank and cannister purge. It 's got a red connection and red valve so it's easy to see. BUt if you left your gas tank loose after getting fuel it sets the same code
the gas cap has to click 3 times to fully seat.
the gas cap has to click 3 times to fully seat.
Dec 5, 2019 at 12:27 PM
(Merged)
Repair Safety Notice: This information is for general instructional purposes only. Vehicle repair can be dangerous. Verify all information, follow manufacturer service procedures, use proper tools and safety equipment, and consult a qualified repair shop when needed.