Will not shift in to park took shift cable off then shifted into park with lever to remove key it will crank only in neutral
Monday, September 7th, 2015 AT 8:28 AM
11 Replies
JACOBANDNICKOLAS
MECHANIC
109,755 POSTS
When you shift it at the lever, does it actually engage into park? If so, it has to be the cable itself is either stretched, broken, or out of adjustment. If it is fully in park and wont start, chances are the neutral safety switch is bad.
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
+6
Saturday, May 1st, 2021 AT 6:24 PM
JOHNNYSILVERWOLF
MEMBER
27 POSTS
No it only goes as for as reverse when shifting it by hand underneath the Guage on the dash reads all gears except park removing cable from transmission only allow me to move column lever to park to remove key
Update removed neutral safety switch and Trans pan found piece hung near outer case image attached don't have no idea what it goes too can you help with that
Was this
answer
helpful?
Yes
No
+8
Saturday, May 1st, 2021 AT 6:24 PM
JACOBANDNICKOLAS
MECHANIC
109,755 POSTS
I can't open the pic. If it is internal, look at the pic I attached and tell me aprox where it is located. Also, if you can save your image as a jpeg, it should open for me.
By the way, I feel confident you found the problem.
Image (Click to make bigger)
Was this
answer
helpful?
Yes
No
-2
Saturday, May 1st, 2021 AT 6:24 PM
JOHNNYSILVERWOLF
MEMBER
27 POSTS
It says jag now
Was this
answer
helpful?
Yes
No
-2
Saturday, May 1st, 2021 AT 6:24 PM
JOHNNYSILVERWOLF
MEMBER
27 POSTS
Finally got a pic of the piece I found hung next to front right case no idea what it is pic is above
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
-2
Saturday, May 1st, 2021 AT 6:24 PM
JACOBANDNICKOLAS
MECHANIC
109,755 POSTS
That looks like the adjuster off one of the clutch bands. If that is the case, and I think it is, my guess is one of the bands is blocking the linkage from shifting to park.
Was this
answer
helpful?
Yes
No
Saturday, May 1st, 2021 AT 6:24 PM
JOHNNYSILVERWOLF
MEMBER
27 POSTS
Sorry so long to update put in new band replaced the anchor still selector will not show park replaced neutral safety switch trans will not lock out still looking for a fix
Was this
answer
helpful?
Yes
No
+1
Saturday, May 1st, 2021 AT 6:24 PM
JACOBANDNICKOLAS
MECHANIC
109,755 POSTS
If it isn't showing park when you shift to it, that sounds like a range sensor. Was the part you posted from the band?
Was this
answer
helpful?
Yes
No
Saturday, May 1st, 2021 AT 6:24 PM
JOHNNYSILVERWOLF
MEMBER
27 POSTS
Yes it was the anchor that goes on the band isn't the neutral/saftey switch the only range sensor on there
Was this
answer
helpful?
Yes
No
Saturday, May 1st, 2021 AT 6:24 PM
JACOBANDNICKOLAS
MECHANIC
109,755 POSTS
They have the range sensor unless you have a 2500 or 3500 series truck. Those actually have a neutral safety switch, but my information is conflicting. In one area of the manual, it indicates what I mentioned above. The next section indicates that only trucks with the 8.0L engine has one.
Was this
answer
helpful?
Yes
No
Saturday, May 1st, 2021 AT 6:24 PM
JOHNNYSILVERWOLF
MEMBER
27 POSTS
Thank you for the help if you come across info on a 46re with a range sensor other then the neutral saftey switch and it's location please let me know and if you think that could be anther reason why it will not lock down so you'd have to push the brake in to switch gears with engine running please let me know on that too