flasher location please

2000 LINCOLN NAVIGATOR
200,000 MILES
Avatar
BUDDY WRIGHT
  • MEMBER
  • 1 POST
no blinkers where is the flasher for the blinkers located?
Jan 7, 2012 at 11:12 PM
Advertisement
Avatar
WRENCHTECH
  • ASE Certified Mechanic
  • 20,761 POSTS
  • ASE Certified Mechanic
It's under the dash near the steering column.
Jan 8, 2012 at 12:05 AM
Avatar
MIKE SUP
  • MEMBER
  • 1 POST
Turn signals do not work I was told it could be either a fuse or the flasher relay Any other suggestions if that does not work
Jul 28, 2019 at 11:47 AM (Merged)
Avatar
KENSMO
  • MEMBER
  • 1 POST
Electrical problem V8 Four Wheel Drive Automatic 109000 miles
----------------------------------------------------------------
All of my turn signals just stopped working. Is there a fuse for this and if so, where exactly is it located in the fuse box? If it's not the fuse, what could be the problem?
Jul 28, 2019 at 11:47 AM (Merged)
Avatar
2CARPRO JACK
  • ASE Certified Mechanic
  • 11,533 POSTS
  • ASE Certified Mechanic
Hello,

There is a relay and fuses that need to be checked to see whats going on. Here are guides the headlight wiring diagrams and fuse locations to help you get the job done.

https://www.2carpros.com/articles/how-to-check-a-car-fuse

and

https://www.2carpros.com/articles/how-to-check-an-electrical-relay-and-wiring-control-circuit

Check out the diagrams (Below)

Please run some tests and get back to us.

Cheers
Jul 28, 2019 at 11:47 AM (Merged)
Avatar
KENSMO
  • MEMBER
  • 1 POST
It was the relay thanks for your help saved me cash for sure I love this site.
Jul 28, 2019 at 11:47 AM (Merged)
Avatar
MHERRINGTON1983
  • MEMBER
  • 1 POST
Vehicle: 1999 Lincoln navigator

original problem: turn signal intermittent problems. Would turn it on and it would blink a few times and either stop all together or "stick" on.

Action: I replaced the multi-function switch.

Current problem: after replacing the multifunction switch, there are now a couple problems. The rear flasher (only the rear) constantly blink. They do stop blinking when I either 1) hit the brakes 2) turn the right or left turn signal on. When I turn the left turn signal on, it works fine. When I turn the right signal on, it only works find as long as I do hit the brakes. As soon as I hit the brakes, it "sticks" on

action: I replaced the turn signal flasher (relay). This didn't make a difference. I still have the same problem.

Any thoughts?
Jul 28, 2019 at 11:47 AM (Merged)
Avatar
HMAC300
  • ASE Certified Mechanic
  • 48,601 POSTS
  • ASE Certified Mechanic
a local guy would have tolook at this it may be a problem with the switch you installed or I fyou have a trailer wiring it may be in there.
Jul 28, 2019 at 11:47 AM (Merged)
Join 2CarPros for free, one of the most advanced car repair communities on the internet. From first-time drivers to seasoned mechanics, everyone is welcome to reply, share details, and get better answers. You can add a temporary image or video first; uploads are limited to 20 MB.
Ask a Free Question
Repair Safety Notice: This information is for general instructional purposes only. Vehicle repair can be dangerous. Verify all information, follow manufacturer service procedures, use proper tools and safety equipment, and consult a qualified repair shop when needed.