Advertisement

Starting and acts like not getting gas

15,000 MILES
Avatar
JPFITCH
  • MEMBER
  • 12 POSTS
2000 Jeep Cherokee 6 cylinder. I have had a problem with my jeep with starting. It will turnover but will not catch on the first try, it will take two or three tries and then it will start sluggish. I have change the purge selinoid and it does not help. In the last month i have changed the fuel filter, fuel pump, crank sensor, and battery. Now my check engine light is coming on with a PO411 error code. Any suggestions?????????
Aug 14, 2012 at 12:27 PM
Advertisement
Avatar
HMAC300
  • ✓Experienced Mechanic
  • 48,601 POSTS
there is no p0411 error code.re read it
Aug 14, 2012 at 12:39 PM
Advertisement
Avatar
JPFITCH
  • MEMBER
  • 12 POSTS
Sorry, the code is P0441.
Aug 14, 2012 at 3:53 PM
Avatar
HMAC300
  • ✓Experienced Mechanic
  • 48,601 POSTS
: EVAP purge solenoid may also be referred to as EVAP canister purge solenoid or duty cycle EVAP purge solenoid. DTC P0204: INJECTOR #4 CONTROL
2. nttAt thistime, conditions for EVAP purge flow monitor failure does not exist orfault is an intermittent problem. Using scan tool, read FREEZE FRAME data while attemptingtoduplicate the conditions that caused CIRCUIT
N t 01: INJECTOR #1 CONTROL
1. Turn ignition on with engine off. Using scan tool, check forDTCs. If DTCSPECIFIC GOODTRIP counter is not displayedandequal to zero, go tonextstep. If DTC SPECIFIC GOODTRIPcounter is DTC P0205: INJECTOR #5 CONTROL
vau )aopol:angine CIRCUIT (4.0L)
5. displayed and equal to zero, go to step 3 . ine warms up to 14 (63.8°C), throttle has bn open for 180 sonds at veclspeed more than 20 M, wth engine speed at 1200 170 RM and MA JECTOR #2 CONTROL
2. DoAt this time, conditions for EVAP purge flow monitor failure doesnot exist or fault is an intermittent problem.Using scan tool, read FREEZE FRAME data while attempting to duplicate the conditions that caused DTC P0206: INJECTOR #6 CONTROL
N CIRCUIT (4.0L)
5. DTC to be set. If DTC P0441:EVAP PURGE FLOW MONITOR FAILURE reoccurs, go to next step. If DTCP0441: EVAP PURGE FLOW MONITOR FAILURE does not reoccur, condition no longer JECTOR #3 CONTROL
op DTC P0300: MULTIPLE CYLINDER
5. exists. Test is complete ine warmsp to 147°F (63.8°C), throttle has been open for 180 secds at vehicle speed more than 20 MPH, with engine speed at 1200 1700 RPM and MAP MISFIRE
M 04: INJECTOR #4 CONTROL
3. Inspect all vacuum hoses for proper routing and checkvacuum hoses from engine to EVAP purge solenoid, and from EVAP purge solenoid to the fuel tank for restrictions. EVAP purge solenoid is mounted on a DTC P0301 P0306: CYLINDER
Der CI
1. bracket at right rear of engine compartment. See Fig. 9 . For vacuum hose routing, see VACUUM DIAGRAMS article. If all hoses are okay, go to next step. If any hoses are improperly routed or restricted, MISFIRE
DT INJECTOR #5 CONTROL
5. repair hoses as necessary.
Aug 14, 2012 at 4:56 PM
Advertisement
Add a reply
Join 2CarPros for free, one of the most advanced car repair communities on the internet. From first-time drivers to seasoned mechanics, everyone is welcome to reply, share details, and get better answers. You can add a temporary image or video first; uploads are limited to 20 MB.

Frequently Asked Problems for This Vehicle