1995 Ford Escort timing

1,222 MILES • 1.9L • 4 CYL • FWD • AUTOMATIC
Avatar
DANSOW
  • MEMBER
  • 4 POSTS
Timing belt broke put in the new one & it will not run all timing marks aligned to tdc changed the firing order still the same
Jul 10, 2014 at 12:22 AM
Advertisement
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
You probably want to check and see if the crank sensor or it's wiring got damaged in the process.

If you don't see anything you will have to go to basic "Crank, no start" testing.

All "crank, no start" conditions are approached in the same way. Every engine requires certain functions to be able to run. Some of these functions rely on specific components to work and some components are part of more than one function so it is important to see the whole picture to be able to conclude anything about what may have failed. Also, these functions can ONLY be tested during the failure. Any other time and they will simply test good because the problem isn't present at the moment.
If you approach this in any other way, you are merely guessing and that only serves to replace unnecessary parts and wastes money.



Every engine requires spark, fuel and compression to run. That's what we have to look for.

These are the basics that need to be tested and will give us the info required to isolate a cause.

1) Test for spark at the plug end of the wire using a spark tester. If none found, check for power supply on the + terminal of the coil with the key on.


2) Test for injector pulse using a small bulb called a noid light. If none found, check for power supply at one side of the injector with the key on.


3) Use a fuel pressure gauge to test for correct fuel pressure, also noticing if the pressure holds when key is shut off.

4) If all of these things check good, then you would need to do a complete compression test.

Once you have determined which of these functions has dropped out,
you will know which system is having the problem.

Jul 10, 2014 at 12:50 AM
Avatar
DANSOW
  • MEMBER
  • 4 POSTS
It will start & run but spits/sputters & backfires then dies after about 1 or 2 minutes it has fire/gas good compression tried to advance and retard the timing with very little change & thanks for your help
Jul 10, 2014 at 1:32 AM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
Something is either assembled wrong or got damaged in the process. Check for stored codes, take a compression test and look everything over again.
Jul 10, 2014 at 1:40 AM
Avatar
DANSOW
  • MEMBER
  • 4 POSTS
After looking over everything for the umpteenth time I was about to put the harmonic balancer back on & I noticed that it has one tooth missing will that make it run rough ?
I'm not sure if it would or not becous the crankshaft sensor would be reading off
Jul 10, 2014 at 7:50 AM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
You mean you can see it broken or it just skipped a tooth?

That's probably normal. That's how it identifies #1 cylinder.
Jul 10, 2014 at 8:14 AM
Advertisement
Avatar
DANSOW
  • MEMBER
  • 4 POSTS
No it has a space witch is factory and I can see a tooth that's been broken off
Jul 10, 2014 at 8:23 AM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
If it's clearly broken, then yes that is a major problem.
Jul 10, 2014 at 8:25 AM
Avatar
DANSOW
  • MEMBER
  • 4 POSTS
I thank y'all so very much for your help
I put a new harmonic balancer on it started up like a new one thanks again
Jul 10, 2014 at 12:21 PM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
You're welcome
Jul 10, 2014 at 7:14 PM
Add a reply
Join 2CarPros for free, one of the most advanced car repair communities on the internet. From first-time drivers to seasoned mechanics, everyone is welcome to reply, share details, and get better answers. You can add a temporary image or video first; uploads are limited to 20 MB.

Frequently Asked Problems for This Vehicle

Advertisement