1995 Chrysler Concorde oil pump

Tiny
BARRYJ
  • MEMBER
  • 1995 CHRYSLER CONCORDE
  • 3.3L
  • V6
  • FWD
  • AUTOMATIC
  • 185,700 MILES
WHERE IS THE OIL PRESSURE RELIEF VALVE LOCATED ON A 95 CHRYSLER CONCORDE WITH A 3.3 LITER ENGINE.
Thursday, October 15th, 2015 AT 11:47 AM

13 Replies

Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
In the oil pump
Was this
answer
helpful?
Yes
No
Friday, October 16th, 2015 AT 9:41 AM
Tiny
BARRYJ
  • MEMBER
  • 7 POSTS
The oil pump is inside the timing cover. But do not see any place for the oil pressure relief valve to go.
Was this
answer
helpful?
Yes
No
Friday, October 16th, 2015 AT 10:24 AM
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
Look in one of the two areas where arrows point in pic
Was this
answer
helpful?
Yes
No
Friday, October 16th, 2015 AT 12:11 PM
Tiny
BARRYJ
  • MEMBER
  • 7 POSTS
That dose not look like the one I have. The one I have has two holes on the bottom. One has a metal cap in it the other slightly larger. But nothing inside either one of them.3.3liter engine the timing cover has water pump made on it.
Was this
answer
helpful?
Yes
No
Friday, October 16th, 2015 AT 3:32 PM
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
The pic is out of a 3.3L Chrysler concorde OIL PUMP BODY
Was this
answer
helpful?
Yes
No
Friday, October 16th, 2015 AT 3:35 PM
Tiny
BARRYJ
  • MEMBER
  • 7 POSTS
The timing cover I have has two holes on the bottom 1for pick up tube an the other blocked off with a metal cap with nothing inside the port. It's about 2 1/2 inches deep. Is that where the pressure valve goses.
Was this
answer
helpful?
Yes
No
Saturday, October 17th, 2015 AT 11:01 AM
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
Here is another pic this is of a 3.5L oil pump which is same as 3.3L if this doesn't match what you have then it's the wrong info given to us.
Was this
answer
helpful?
Yes
No
Saturday, October 17th, 2015 AT 1:18 PM
Tiny
BARRYJ
  • MEMBER
  • 7 POSTS
95 Chrysler Concorde had new oil pump an pressure switch. But oil lite come on when warmed up at idle. When I rev engine hose out. When I am driving it comes on every time I stop. But no tapping of any sort. Helpless
Was this
answer
helpful?
Yes
No
Thursday, October 22nd, 2015 AT 6:18 PM
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
I tmay be that thee is to much bearing clearance in it causing this. You can try a different oil filter like a Purolator or wix or napa sometimes that is the problem. Also try switching to 10w30 oil if you aren't already.
Was this
answer
helpful?
Yes
No
Friday, October 23rd, 2015 AT 6:14 AM
Tiny
BARRYJ
  • MEMBER
  • 7 POSTS
Changed oil to 10 w30 an filter to a wix. Oil lite still come on. Fine while driving but when I stop lite comes on and at idle rev engine up lite goes out. No valve noise or engine rattle. New oil pump/ new filter n oil. HELP.
Was this
answer
helpful?
Yes
No
Sunday, October 25th, 2015 AT 3:44 PM
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
Ou have to much clearance in your rod or main bearings or both.
Was this
answer
helpful?
Yes
No
Sunday, October 25th, 2015 AT 5:02 PM
Tiny
BARRYJ
  • MEMBER
  • 7 POSTS
What are the damages that it may cause. And what is good fix.
Was this
answer
helpful?
Yes
No
Sunday, October 25th, 2015 AT 5:39 PM
Tiny
HMAC300
  • MECHANIC
  • 48,601 POSTS
You may be getting in over your head now, the crank has to be measured to make sure there is nowear there and engine bearings will need to be replaced. Other wise pull the engine an dput what is called a crank kit in it which is another crank and bearings, that is assuming the rods have not spun a bearing etc. If that has happened then you may as well rebuild motor.
Was this
answer
helpful?
Yes
No
Monday, October 26th, 2015 AT 7:45 AM

Please login or register to post a reply.

Sponsored links