SPONSORED LINKS

Crankshaft sensor location

Tiny
ANONYMOUS
  • MEMBER
  • 1992 PONTIAC SUNBIRD
  • 68 MILES
Where is the crankshaft sensor located on the Pontiac Sunbird with a 3.1 engine?
Wednesday, February 6th, 2013 AT 8:26 PM

10 Replies

Tiny
RASMATAZ
  • MECHANIC
  • 75,992 POSTS
Hello,

The crankshaft sensor is located on the right side of engine. Here is a guide to help walk you through the steps and a diagram below to show you the location.

https://www.2carpros.com/articles/crankshaft-angle-sensor-replacement

Check out the diagrams (Below). Please let us know what happens.
Image (Click to make bigger)
Thumb
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
-1
Wednesday, February 6th, 2013 AT 8:37 PM
Tiny
WUTSUPY
  • MEMBER
  • 59 POSTS
  • 1990 PONTIAC SUNBIRD
  • 4 CYL
  • FWD
  • AUTOMATIC
  • 90,000 MILES
Where is the crank position sensor on a 1990 Pontiac sunbird with a 2.0 motor and it has a distributor. I was told it was under the timing belt cover. Please help
Was this
answer
helpful?
Yes
No
+3
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
MMPRINCE4000
  • MECHANIC
  • 8,548 POSTS
I checked my parts book and it does not show a crank sensor for the car.
Was this
answer
helpful?
Yes
No
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
WUTSUPY
  • MEMBER
  • 59 POSTS
Hmm mine shows one for the 1992 with the same motor so I was double checking
Was this
answer
helpful?
Yes
No
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
WUTSUPY
  • MEMBER
  • 59 POSTS
Do you know what triggers the fuel injector to inject gas, that is my real problem
SPONSORED LINKS
Was this
answer
helpful?
Yes
No
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
VERN1939
  • MEMBER
  • 15 POSTS
I have same problem, but to much gas

New throttle body fuel sensor no change to much gas
Injector seems to be ok but no pulse toit.
Vern1939
Was this
answer
helpful?
Yes
No
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
WUTSUPY
  • MEMBER
  • 59 POSTS
Ok I was told to check the ignition module, how do I pull it out, and more importantly, how do I test it?.A few minutes latter, I just pulled it out, on the side with 3 prongs I get power to 2 of the 3 prongs, the one I dont get power to is labled B, is this my problem, and if itisnt I need to know how to test the module, with ohms? Or?
Was this
answer
helpful?
Yes
No
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
ALMW
  • MEMBER
  • 2 POSTS
  • 1994 PONTIAC SUNBIRD
  • 4 CYL
  • FWD
  • AUTOMATIC
  • 94,000 MILES
I need to know what is a crank sensor and why my car wouldn't run without it?
Was this
answer
helpful?
Yes
No
+1
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
BLUELIGHTNIN6
  • MECHANIC
  • 16,542 POSTS
A crank sensor is a component used in an internal combustion engine to monitor the position or rotational speed of the crankshaft. This information is used by engine management systems to control ignition system timing and other engine parameters. Crank sensors in engines usually consist of magnets and an inductive coil, or they may be based on magnetically triggered Hall effect semiconductor devices. Common mounting locations include the main crank pulley, the flywheel, and occasionally on the crankshaft itself. This sensor is the most important sensor in modern day engines. When it fails, there is a small chance the engine will start (engine will likely cut out after a few minutes of driving) but it mostly will not start
Was this
answer
helpful?
Yes
No
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)
Tiny
ALMW
  • MEMBER
  • 2 POSTS
Thanks you answer explained a lot. I had never heard of the crank sensor before.
Was this
answer
helpful?
Yes
No
Wednesday, January 16th, 2019 AT 7:22 PM (Merged)

Please login or register to post a reply.

Related Crankshaft Sensor Location Content

VIEW MORE

Sponsored links