1990 suburban wont start

80,000 MILES • 5.7L • V8 • 4WD • AUTOMATIC
Avatar
WYATTGC
  • MEMBER
  • 5 POSTS
1990 burb, v1500 350 tbi 80k miles. It sat for the better part of a decade.
Changed the tank, pump, sending unit. map sensor tps sensor,
plugs/wires, and the iac valve. It was running fine (did blow the gauge
cluster fuse a while back) Went to the store and parked, came out and no
dome lights, gauge lights, headlights, radio nothing. It cranks, gets spark
but wont fire. Turn signals work, check engine light doesnt come on. I'm at
a loss. I don't get fuel pressure/the pump doesn't turn on. The battery is
BRAND new (switched it out with another known good one to make sure.)
Also the reel light works under the hood. All fuses under the steering
column are good.
I'm at a loss here.
What should I check first? thanks
Jan 16, 2016 at 6:44 AM
Advertisement
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
Does the check engine light come on for bulb check when the key is first turned on?
Do you have injector pulse?
Jan 16, 2016 at 7:08 AM
Avatar
WYATTGC
  • MEMBER
  • 5 POSTS
The check engine light does not come on and the injectors don't pulse. There is power getting to the fuel pump. no it doesn't turn on and still no lights whatsoever (just turn signals work)
Jan 16, 2016 at 8:37 AM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
If the check engine light doesn't come on for bulb check then your computer is not powering up. You need to check those fuses in the engine compartment better. Use a test light.
Jan 16, 2016 at 8:39 AM
Avatar
WYATTGC
  • MEMBER
  • 5 POSTS
I've check and rechecked the fuses under the steering wheel, all the ones in the fuse box are good. What fuses in the engine compartment do i need to check and where are they?
Jan 16, 2016 at 8:59 AM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
You need to see if the "ECMB" fuse has power in and out with the key on.
There are also fusible links to check. They will be either at the starter or a junction block in the engine compartment.



Jan 16, 2016 at 9:19 AM
Avatar
WYATTGC
  • MEMBER
  • 5 POSTS
The ECMB does not have power in or out, the ECM does however, thanks a ton by the way.
Jan 16, 2016 at 10:00 AM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
Move onto the fusible links
Jan 16, 2016 at 10:04 AM
Avatar
WYATTGC
  • MEMBER
  • 5 POSTS
Can you check fusible links with a test light? I don't have much experience with them. Also, anything I should check for? Would a bad fusible link cause my lights and fuel pump not to work?
Jan 16, 2016 at 12:15 PM
Avatar
WRENCHTECH
  • ✓Experienced Mechanic
  • 20,760 POSTS
Fusible link are special sections of wire that melt when overloaded. You can check them by pulling on them and if they stretch, they are burnt internally. Use only fuse wire to replace that section. NEVER regular wire. These links feed the fuse boxes so you can lose many functions with one burnt link.
Jan 16, 2016 at 12:19 PM
Add a reply
Join 2CarPros for free, one of the most advanced car repair communities on the internet. From first-time drivers to seasoned mechanics, everyone is welcome to reply, share details, and get better answers. You can add a temporary image or video first; uploads are limited to 20 MB.

Frequently Asked Problems for This Vehicle

Advertisement